posted
02/08/09
by Xavier Toolhausens
Tire pressure gauges are an important tool used in . These diagnostic tools let you know how much air pressure is sitting in the tire. The air pressure in the tire is of the utmost importance because any deficiency or overage of air, inside the rubber, can result in a car accident.
Inefficient air pressure, or too much in a vehicle’s tire, can result in the loss of control for the driver. When the tires are low, the car will jerk to the side having more pressure. On the other side of the coin, overfilling a tire can result in a drag of the automobile’s steering to the side that has less pressure. With this issue, it is extremely vital to make sure the tire is filled to its specified PSI (pressure per square inch), and the exact pressure for the four tires. For example, if you are filling the rubbers 5 PSI, then repeat for each of the four tires.
Not only is it bad to have insufficient pressure or too much pressure, it is just as harmful when you are checking the tire’s air pressure. When gauging the air inside a tire, follow the steps below:
1. Read the manufacturer’s listed PSI you must pump the tires to. This listing is typically written on the side wall of the tire. It is safe to inflate the tires a maximum of5 PSI less than what is suggested. However, it is not suggested to pump them any more than what is listed. The typical automobile’s tires almost all take about 35 PSI. Though, to reduce the risk of being injured, it is suggested that you read the tire to make sure.
2. Turn away from the tire while fitting the gauge to the air stem on the tire. Hold the tool to the stem of the tire. Move it until you do not hear any air escaping. Look at the gauge and record your findings.
3. If the gauge shows 0 PSI, then it means you are in desperate need of air. If this happens, fill the tire(s) until the maximum PSI.
4. Read the pressure after the fill with the gauge. It should read some level of PSI once inflated passed about 10 PSI.
5. Then, fill and stop when reaching the maximum PSI required for the tire. Again, you do not want to go over the maximum specified PSI as designated by the tire manufacturer.
Not following the above list when measuring the pressure with a gauge can be very harmful. If a tire is inflated past the recommended PSI, it can pop, sending pieces of tire and metal at the speed of a bullet. Most tires today are fabricated with steel belts to bend the rubber together. This steel can become a lethal weapon that can injure you if you are not careful. There have actually been deaths from over inflating car tires.Ensure you do not risk injury by remembering to be safe.
About the Author:
Xavier is a journalist with more than fifteen years editorial experience. Xavier is presently working as a reporter for the fuzing.com portal and has become the resident expert on automotive safety. Visit our useful website for more information on
Tire Gauges and
Pressure Gauge.
posted
23/07/09
by Xavier Toolhausens
Tire pressure gauges are valuable monitor used in the diagnostics of a motor vehicle. These significant tools let you know how much air pressure is in the tire. The air pressure in the tire is extremely important because any under fill or overage of air, inside the rubber, can throw of a multitude of normal car operations.
Inefficient air pressure, or too much in a vehicle’s tire, can hurt you badly. When air is low, the car will jerk to the side that has more tire pressure. On the other side of the coin, overfilling the air can bring about a drag of the automobile’s steering to the side that has less pressure. With this issue, it is extremely vital to check to see the tire is filled to its manufacturer’s specification PSI (pressure per square inch), and an equal PSI for the four tires. Therefore, if you are filling them 5 PSI, then all get filled to 5 PSI.
Not only is it dangerous to have not enough pressure or too much pressure, its equally as hazardous when filling the tire pressure. When measuring the air in a tire, follow the steps below:
1. Find the manufacturer’s listed PSI you must inflate the tires to. The specification is usually on the side wall of the tire. You can, if you like, inflate the tires no more than5 PSI less than what is suggested. But, it is never ok to fill them any more than the recommendation. Typical car tires these days take about 35 PSI. However, it is better safe then sorry so its best to check.
2. Aim your face away from the tire before attempting to check the air pressure. Hold the tire pressure gauge to the stem of the tire. Move it until no pressure is hissing out. Look at the gauge and read the results.
3. If nothing happens then it should you are in desperate need of air. If this is the case, inflate to the maximum PSI.
4. Check the pressure again with the gauge. It should give an accurate reading once you get passed about 10 PSI.
5. After this, fill as necessary to come close to the maximum PSI required for the tire. Again, it is dangerous to inflate above the maximum recommended PSI as designated by the tire manufacturer.
Failing to follow the above suggestions when reading air with a gauge can result in injury. If a tire is overinflated, it can pop, sending pieces of tire and metal at the speed of a bullet. Most tires nowadays are made with metal belting to tighten the rubber together. This stuff can turn into flying razor blades that can injure you if you are not careful. People have been killed from over inflating vehicle tires.Ensure you do not risk injury by protecting yourself and those around you.
About the Author:
Xavier Toolhausens is a publicist with over 15 years writing experience. Xavier is currently employed as a reporter for our b2b site and has become the in house specialist on car accessories. Be sure to visit our useful web portal for additional information on
Tire Pressure Gauge and
Digital Tire Gauges.
posted
23/07/09
by Xavier Toolhausens
Tire pressure gauges are an important tool used in checking air pressure in an automobile. These significant tools let you know how much air pressure is present in a tire. The air pressure in the tire is very crucial for any missing air or overage of air, in them, can cause your car to go out of control.
Inadequate air pressure, or too much in a vehicle’s tire, can result in the loss of control for the driver. When air is low, the car or truck will lean to the side that has more tire pressure. On the other side of the coin, overfilling a tire can create a drag of the automobile’s steering to the side with less air. With this being said, it is extremely vital to check to see the tire is filled to its specified PSI (pressure per square inch), and an equal PSI for each four tires. So, if you are filling your tires 5 PSI, then repeat for each of the four tires.
Not only is it bad to have insufficient pressure or a lot of pressure, its equally as hazardous when filling the tire pressure. When gauging the air inside a tire, you should do the following:
1. Check the manufacturer’s specification for the PSI you should fill the tires to. The specification is usually on the outside surface of the tire. It is safe to inflate the tires down to5 PSI below the suggestion. However, it is not suggested to inflate them any more than the specified PSI. Typical car tires almost all take approximately 35 PSI. However, it is better safe then sorry so its best to check.
2. Aim your face away from the tire prior to checking the level of air. Hold the tool to the nozzle of the tire. Steady it and center it until there is no spare air leaving the tire. Look at the gauge and read the results.
3. If the gauge shows 0 PSI, then it should you are in desperate need of air. If this is the case, inflate up to the maximum PSI.
4. Read the pressure again with the gauge. It should give an accurate reading once inflated passed about 10 PSI.
5. Then, fill until you achieve the maximum PSI suggested. Again, you do not want to go over the maximum specified PSI as calculated by the tire manufacturer.
Failing to follow the above steps when measuring the pressure with a gauge can be very harmful. If a tire is overinflated, it can explode, sending chunks of the metal belt directly into your face. Most tires today are fabricated with steel belts to tighten the rubber together. This stuff can turn into flying razor blades that can injure you if you are not careful. There have actually been deaths from over inflating automobile tires.You can seriously reduce the risk injury by remembering to be safe.
About the Author:
Xavier Toolhausens is a publicist with over 15 years writing experience. Xavier is currently employed as a reporter for our b2b site and has become the in house specialist on car accessories. Be sure to visit our useful web portal for additional information on
Tire Pressure Gauge and
Digital Tire Gauges.
